Cell Mill for Zirconium Silicate

With the development of the times, the progress of society, the development of the market is elegant, and more and more manufacturing have to accelerate innovation, some transformations, some continue to improve the technical level of the product, to adapt to the development of the market, Meet the customer's picky requirements. In the case of changing market, only constantly innovation, continuously improve your technical level, constantly improve your own products, in order to make the Cell Mill for Zirconium Silicate industry have a broader development space.

In terms of airflow milling, it is important to understand its operational rules, which is very important because only familiarize the procedure, can operate correctly.
1. The operation rules of Cell Mill for Zirconium Silicate are as follows: Prepare materials before the start of the production order, prepare materials. Complete the site to clean the grocery. Check whether the transportation pipes and auxiliary equipment, whether the pipelines are blocked, leak or poor sealing, whether the auxiliary equipment is intact, whether it works normally. Whether there is a phenomenon that the material is accumulated in the outer casing and the separator, if the accumulated material is required. Whether the bearing is lubricated, whether it is lubricated in an appropriate place. Check if all pipes, fastening bolts, washers, spindles, and instruments are intact, normal and flexible.
Second, Cell Mill for Zirconium Silicate starts the motor, control the current and time at starting, so that the device can start running. When the equipment is operating normally, the feed speed can be adjusted according to the properties of the material. Uniform continuous feed should not be large or small, thereby affecting the separation effect of the grinding machine, making the machine easily malfunction. During operation, if an abnormality occurs, stop checking immediately before the failure continues.
Third, the main procedures of the close and inspection of Cell Mill for Zirconium Silicate are as follows: After the material in the grinding machine housing is completely pulverized, the feed should be stopped and turned off the motor. After the machine is idling for 3 minutes, press the stop button to stop the machine. When the machine is completely stopped, open the check door and check the wear of the vessel. Fill in the corresponding production record, update the device status flag, which is convenient for the next use.


ALPA Trimats Cell Mill for Zirconium Silicate Case Sharing: The company requires a three-dimensional material ultrafine pulverizer, and our AlPa's Cell Mill for Zirconium Silic is also more famous in the industry. of. There is a lot of proportion in the industry. Through experiments, the company purchased a Cell Mill for Zirconium Silicate of our company.
Technical parameters:
Finished granularity: D50: 10μm

In order to have a further understanding of Cell Mill for Zirconium Silicate, the following is simple to analyze common problems and how to solve it. these questions.
1, ask: How to choose equipment in the face of materials that need to be smashed?
A: (1) Moh's hardness is less than 3. The mechanical grinding machine and hierarchical impact mill can meet the crushing requirements, saving a certain cost. (2) High hardness, high purity material is higher than 3.5 hardness. (3) If it is a metal powder, you can atomize the grading and cannot be broken.

A: (1) After the food and drug is crushing, it is necessary to meet the level of food safety, the best choice for stainless steel materials, because the mirror is polished inside and outside, does not produce iron pollution. (2) Broken material is easy to worn, and the purity is required to be high after crushing, and the stainless steel is optimal. (3) If the crushing requirements are not high, cost savings, the air pulverizer of carbon steel material can be used.
3, ask: When using a gas flow crusher, the fineness of the finished product does not reach the standard, how to adjust the classification wheel is not used?
A: (1) If the new custom pulverizer does not meet the requirements of the granularity, the device can be incorrect.
Therefore, in order to avoid such errors, it is best to perform material crushing and grading experiments before purchase, and carefully check whether the experimental results are satisfactory.
The equipment market is changing. At present, Cell Mill for Zirconium Silicate has certain demand in the market, but the society is constantly evolving, no matter what industry needs to keep paying with the times, it can lead the industry.