Vibration Mill for Wheat Germ

Vibration Mill for Wheat Germ is mainly used by the pulverization mechanism determines its scope, high finished product and improvement, widely used in chemical, minerals, metallurgy, abrasives, ceramics, refractories, pharmaceuticals, pesticides, food, health care. Products, new materials and other industries.

What factors affect the performance parameters used by the Vibration Mill for Wheat Germ?

The following is a detailed description:

1. Feed particle size control

Most Vibration Mill for Wheat Germ has a certain upper limit requirement for feed particle size. After entering the pulverization cavity, it can be sufficiently accelerated before collision and crushing with other particles. It is difficult to completely accelerate after large particles enter the pulverized cavity, which will allow them to stay in the machine too long, resulting in too high energy consumption. Therefore, in large-scale production of ultrafine powder, it is an effective way to pre-ground the raw material of the particle size is an effective pathway for energy saving.
2. Working medium

Currently, the working medium of Vibration Mill for Wheat Germ is mainly compressed, superheated steam, inert gas, and the like. The choice of working fluid has a certain impact on crushing effects and economics. Superheated steam is superior to air in fluidity and critical flow rates to achieve higher flow rates and uniform flow fields. However, using superheated steam as a working fluid, it must be ensured that it is still in an overheating state before entering the product capture device, otherwise the material is condensed.
3. Feeding speed

Feeding speed is an important parameter reflecting gas flow grinding production capacity. During the pulverization process, the optimum ratio of the intake flow rate and the feed speed is the key to improving the crushing efficiency. In general, under certain intake flow conditions, the feed speed is proportional to the particle size of the product. However, the feeding speed is too fast, which will increase the particle density, mutual interference, disadvantage of the particles, and difficult to achieve the sufficient and effective collision between particles, affect the crushing effect; although the feed speed is too slow, the particles stay in the crush area The time can be extended, which will reduce the particle density, reduce the collision rate, resulting in a decrease in production capacity and an increase in unit production energy consumption.
4. Granular limit

Vibration Mill for Wheat Germ In the pulverization process, as the material particle size is reduced, the crystallization and intensity of the material increases. After reaching a certain degree, the particle size of the material is no longer reduced or reduced, that is, the crushing limit of the material is reached. At this time, the material specific surface area increases, the surface activity of the particles, the particle agglomeration and grinding are in a dynamic equilibrium state, even if the grinding time is prolonged, it is difficult to further reduce the particle size of the material.



ALPA Trimetic Cobalt Sites Vibration Mill for Wheat GERM Case Sharing:
A new energy technology company is a professional use of lithium-ion power batteries for new energy vehicles, storage capacity High-tech enterprises in the R&D and industrialization of key materials of lithium-ion batteries and lithium-ion batteries, the first power battery enterprises that realize large-capacity manganese-based lithium-ion battery scale production and marketization applications.

Product particle size: D50: 3-25μm
Hours Yield: 3-10kg

Temperature rises in the bearing must often be checked frequently in the production process, when the temperature rise exceeds 50 At ° C, the check is stopped, and the reason is to troubleshoot. When the new machine is running, the drive belt is easy to elongate, pay attention to adjust the proper looseness of the belt to ensure the work life of the belt. If the lifting piece should be checked frequently, replace the production quality and production in time. The blade, the bushing should often check the wear situation. If the wear is worn, the productivity decreases, and the particle size is roughly discovered to be replaced. The host and the grading flow bearing are lipomatic lubrication, using special lipids, the replacement period of the bearing is around three months, and the filling of the grease is 1/2 of the interior space in the bearing cavity. Otherwise, It will cause too high of the bearing temperature. The spiral feeder has changed the lipid period of half a year, and Cape Calcium-based grease. In the output shaft E, ie the pulley E, avoiding the weight of the weight, damage the part. It is strictly forbidden to turn the handle on the stop. The lubricating oil used in this regulator is used with N32 alkaline high-zinc high-grade anti-motor oil pressure oil, and the deceleration machine is 401 generally lubricating oil, and it is not necessary to use other machines. After four or five months, new oil should be replaced.