Impact Mill for Chrome Oxide Red

Many friends who want to produce industrialized are certainly unfamiliar with Impact Mill for Chrome Oxide Red. Impact Mill for Chrome Oxide Red has features that have convenient, unclear, crushing product quality, is a very useful Crush machine.

Impact Mill for Chrome Oxide Red is mainly used for more refined materials. The pulverized particle diameter is 1.5 to 0.005 mm, and the crude material is sieved.
The principle of pulverization is substantially the same as the hydraulic level, and the above settlement theory can also be used for airflow classification. However, in the airflow classification, since the density and viscosity of the air are much smaller than the density and viscosity of water, the same particles are more settle more in the air than in the water. Moreover, the density and viscosity of the air varies with temperature and pressure.
In order to cause air flow, wind pulverization equipment typically requires an appropriate fan (exhaust or blast).

When the airflow is classified, the fine particles are typically taken away by the airflow. In some cases, the raw material is sent to the gas stream into a pulverized device.

It is well known that the load of solid particles in air under normal pressure does not exceed 500 g / m3 air. When it reaches 1 kg / m3, the particles fall from the airflow. The load is related to the density and particle size of the particles. When the fine particle material is treated, the load generally does not exceed 200 to 300 g / 3 air. According to this calculation, the volume concentration of the solid in the gas stream is much smaller than 0.03. Therefore, when the airflow is classified, in most cases, it belongs to the free settlement.

The speed required to move the particulate material in the horizontal and vertical directions is relatively large, and the speed required in the horizontal direction is relatively large, and as the particle density increases, for example, for the density 1.5 of the pulverization coal per centimeter. The minimum wind speed is 2 m / sec; a powder material having a density of 2.5 g / cm, the speed is not less than 3.5 m / sec; a powder having a density of 4 g / cm 3, a minimum speed of 4 meters per second. Due to the complexity of the situation, the appropriate airflow rate in each particular situation should be determined by experiments.

In the rising airflow, the airflow speed required to suspend a certain density and particle size is greater than the calculated value of free settling, which is due to the uneven distribution of the airflow along the pulverizing chamber portion.

The Impact Mill for Chrome Oxide RED has a wide comminuted range, high pulverization efficiency, high pulverization precision, accurate cutting particle size, and good stability.
ALPA crystal sorbitol Impact Mill for Chrome Oxide Red case Sharing: Taiwan's cosmetics companies need a large amount of crystal sorbitolCrushing production line, through our Actors of Shandong AlPa, I learned that our company can customize the commissioning equipment. After many incident experiments. I finally purchased a company Impact Mill for Chrome Oxide Red.
Technical parameters:

Production capacity: 10T


The factors affecting the operation efficiency of Impact Mill for Chrome Oxide Red Devices have the following points: [ 123] 1. Material performance, in general, air pulverization equipment can adapt to all brittle materials, but due to different material properties, the pulverization performance is also different, due to strength, density, hardness, viscosity, shape and electricity of different materials. The performance is different, which will inevitably lead to the difference in crushing effect. The strength of the material is an important factor. The water content of some materials will change the performance, toughness and viscosity of the crushing material, and the fineness of the pulverized material will produce noise.
2. If the processing capacity of the device is the same, if the processing material is different, the grinding fineness will be different. In general, the processing capacity of the airflow grinding machine is proportional to the particle size of the product.

Shandong AlPa is a well-known particle and powder processing system supplier, which is committed to the change of traditional powder industry. We provide customized and passed CE certified products: airflow pulverizer, mechanical pulverizer, airflow classifier, ball milling production line, surface modification production line, etc. In the field of medical, food, chemical, minerals, new materials, solid waste treatment, we have a mature full-specific solution. We provide more than just machines. We help you design the ideal system to meet your needs. In the past 20 years, \"the future\" of the advanced materials in powder technology \"has always been our company mission. We look forward to and desire to embrace the future. To this end, we have made full preparation. We wish to grow together with you.